Quarrying of stones-Definition, various methods, and precautions

Quarrying of stones-Definition, various methods, and precautions


In this article, we will discuss the quarrying of stones by various methods and the precautions to be taken while quarrying and the selection of a suitable site for the quarrying process.


Definition: Quarry is defined as the place or the region from where the stones are obtained.
The process of extracting stones from rocks or natural bed is known as quarrying.

Quarrying of stones

For civil engineering purposes for masonry construction, road construction material, railway tracks, as aggregate in concrete and for many local other purposes.

Also, read: Salary of a civil engineer

The common important terms used in quarrying are as follows:


1)Blasting: Quarrying with the help of explosives such as gunpowder or dynamite
2)Safety fuse: It is a wire consisting of short length and with burning composition
3)Tamping: The operation of filling the hole containing explosive with sandy clay
4)Quarry sap: It is the moisture present in the quarried Stone
5)Line of least resistance: It is the horizontal distance between the outside the surface of Rock to the hole of blasting



Methods of quarrying:

Quarrying is done by the following methods:
1)quarrying by hand tools
2)quarrying by channeling machine
3)quarrying by blasting

Quarrying by blasting is usually preferred than the two methods

In this, we will discuss quarrying by hand tools and quarrying by blasting

1)Quarrying by hand tools:


This is also done in three ways
  • Quarrying by excavating
  • Quarrying by heating
  • Quarrying by wedging

Equipment:

  • Pickaxes
  • Hammers
  • Showels
  • Chisels
  • Crowbars
  • Steel pin

  • Quarrying by excavating: This method is suitable for soft rocks such as sedimentary rocks. The stones are obtained by the help of hammers, chisels, showels.
  • Quarrying of stones

  • Quarrying by heating: In this method rock is heated using fuel and due to expansion rock cracks. The stones are obtained by pickaxes, showels, etc

  • Quarrying by wedging: This is one of the usually preferred method then the above methods.
In this method number of holes is drilled on the surface of the rocks in an alignment. The diameter of the hole is about 12 mm and death about 100 to 200 mm at a uniform distance of 100-150mm.

Quarrying of stones

Method: As shown in the figure after drilling holes, feathers and plugs are put in the holes. The top of the plugs are simultaneously driven till the rock cracks along the alignment

This method of quarrying is suitable for sedimentary rocks and also for soft rocks.

Watch this video for a better understanding:




2)Quarrying by channeling Machine:

In this method channeling machine driven by compressed air or electricity is used for quarrying of stones.with the help of machines grooves or channels can be cut to a depth of 2.4 to 3.5 m .the stone blocks are cut down and conveyed with the help of conveyor of short length.
This method is carried out for limestone, sandstone and for other soft rocks. 


Quarrying by blasting:

This method is for hard and compact rocks and for large quarrying process. In this method, a large rock is separated by the use of explosives.


Equipment:

The following equipment is used for blasting:

  • Dipper
  • Jumper
  • Priming needle
  • Scrapping spoon
  • Tamping bar
  • Explosives
  • Copper cylinder
  • Fuses


Operation process for blasting:


Quarrying of stones


1) The blast holes are made with the help of jumpers, dippers, and spoon.
2) Then clean the blast holes with the help of cloth
3) The quantity of explosives(i.e gunpowder or dynamite) is poured into the hole
4) Has shown in the figure the remaining portion is filled with clay or  
Moorum
5) The brimming needle of 2 mm diameter is inserted to reach the gunpowder. Then it is slowly withdrawn leaving narrow space.
6) A fuse is introduced in the narrow space.
7) The free end of the fuse is fired with a match stick or with electricity.
8) Finally, an explosion takes place and the rock is disintegrated into small stones that are used for the engineering purposes.


Precautions to be taken in blasting:



  1. The blasting area boundary should be with caution boards, red flags, etc.
  2. The tamping bar should be of copper and not steel.
  3. Blasting should be carried out the trained and experienced person.
  4. The fuse should be longer so that can escape from the area.
  5. The explosives should be stored properly.

Selection of the site for quarry:


  • The site should be so selected that the power, materials and labor should be available near the site.
  • The distance of the Quarry site should be minimum for the transportation facilities.
  • The site so selected should be economical.
  • Facilities such as tractor, trucks, JCB should be available for carrying stones.
  • There should not be any Radioactive Rays in the site.
  • The site it should be from residential areas.
  • The site should be such that it should not cause disturbance to the people residing near the site.
  • Space for disposal should be available near the site.



    



Post a Comment

0 Comments